Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
Were you trying to find ideas around How to Install a Bathtub?
Installing a tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably difficult task. If the old bathtub is readily available, the project can move speedily; if you need to open a wall surface to get rid of the old tub and place the new tub, the task is a lot harder. In either case, the job is within a house handyman's abilities, although you will need a helper to vacate the old tub and also embeded in the new one. Make certain you have certified yourself for the task and also are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed task, it is better to think about employing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you set up a brand-new tub in your restroom if you have currently bought a new bathtub and don't require to change the setup of your previous water supply pipelines.
Your tools and also product checklist need to comprise the following:
Planning for the Installation
First of all, the supporting framework provided with the bath must be fitted (if called for) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps device to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be fairly problematic due to the limited access that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the remaining water that will originate from the pipelines. As soon as the supply pipes have been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Before moving on to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bath tub till the level checks out level.
To mount taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the water supply as well as check all joints as well as new pipework for leakages as well as tighten them if essential. Fill up the bath tub and likewise examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bathtub needs to wait until the tub has been made use of at least once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin guaranteeing that the washers remain in location between the tap as well as the sink. Secure the tap in position with the manufacturer offered backnut. As soon as the tap is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous type ought to be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, bring about issues with wetness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in usage. The sealer can crack rather very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily offered on the marketplace. It is advisable to fit the tiles using waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very serious about Tools You Need to Install a New Bathtub and I really hope you appreciated the new article. Loved our content? Please share it. Let others locate it. Thanks so much for going through it.
This Page Report this page